Home > Side by Sides > Polaris > Xpedition > Intake and Exhaust > Aftermarket Assassin AA Dual Suppressor Slip-On Exhaust for Polaris Xpedition (1-3 Day lead Time)

Aftermarket Assassin AA Dual Suppressor Slip-On Exhaust for Polaris Xpedition (1-3 Day lead Time)

0 Review(s)

Your Price: $795.00

Please Always Call to Verify Stock

Free Shipping.

Part Number:110-1019

Quiet Core or Spark Arrestor (optional)

ADV or Dump Bed Model

Quantity

Description
Customer Reviews

Fits all 2024+ Xpedition models
**Will NOT fit with most rear bumpers**
This stainless steel AA slip-on exhaust is just what your machine needs! We set out to produce an exhaust that adds power, looks great, and sounds great... without being obnoxiously loud.
With our dual muffler design, this exhaust sounds amazing with a nice deep tone but not significantly louder than the OEM exhaust. At idle and off idle you will notice a bit more rumble but when moving, this exhaust is within 2 dB of the stock exhaust. The deeper tone helps cover up some of the engine noise/drone.
Gain 7-8 RWHP! In our initial testing, we could instantly feel the difference with this exhaust and saw a 200-300 RPM gain. The dyno backed this up by showing us the gains and just how quickly they came on. The best thing about this exhaust is the ability to run our Cruiser clutch setup and still see a power gain. When clutched fully loaded with our Cruiser weights, we only lost 2-3 RWHP when compared to being clutched for 8400-8500 RPM. At higher speeds the Cruiser kit dropped off a bit more, but 0-40 MPH acceleration was barely affected. This is a big deal, as with the OEM exhaust you lose much more power with our Cruiser setup. This exhaust really shines everywhere, especially in the mid-range.
Dyno graph is shown with 32" tires which showed a gain on the dyno due to building speed quicker. See a list of power levels on 32" tires below.
Stock with 32" Tires = 96 RWHP
Stock with Cruiser clutch setup = 86 RWHP
S3 Cruiser clutch kit + L1 Flash = 88 RWHP
S3 Clutch Kit (not Cruiser) with stock ECU = 100 RWHP
S3 Clutch Kit (not Cruiser) and L1 Flash = 103 RWHP
S3 Cruiser Clutch Kit + Exhaust + L2 Flash = 108 RWHP
S3 Clutch Kit (not Cruiser) + L2 Flash = 110 RWHP
If you'd still like less sound, you can install our 1.5" Stealth Quiet Core. Installing this core drops horsepower and sound back to factory levels with nearly the same note.
Can use your OEM spark arrestor in this exhaust or purchase our spark arrestor.
** Exhaust cannot be used with both the spark arrestor and 1.5" stealth core at the same time**
Much better airflow which is needed to decrease heat (especially when tuned)
Eliminates the stock catalytic converter which creates a ton of exhaust and motor heat
+7-8 RWHP with our Level 2 ECU flash for proper fueling
Fits nicely into the factory location and allows bed to dump
**May NOT fit with some rear bumpers like the OEM Polaris one**
Made at the AA Facility in the USA!
Sharp corners and outlets designed to match the Xpedition styling
Hydroblasted finish with rust inhibitor (Yes, even stainless can still develop surface rust) - The stainless will bronze and matches the stock header very well
Can be used with the factory tune or our Level 1 tune without issue, but will run even better and gain the most power with our Level 2 tune designed for this exhaust.